Car moto

Simplified Brake Disc Replacement Guide for Your Peugeot 207: Achieve it in 5 Easy Steps!

On June 12, 2024 , updated on June 12, 2024 - 14 minutes to read

IN SHORT

Necessary tools for changing the brake discs of your Peugeot 207: jack, jack stands, spanner, flat screwdriver, ratchet, brake cleaner, suitable brake discs.
🛠️

Vehicle preparation with the jack and jack stands, removal of the wheel, access to the brake caliper.
🚗

Removing the brake disc worn, installation of the new disk, reassembly and checking.
🔧

Checking the material : jack, jack stands, adjustable wrench, brake lubricant.🔩

Disassembly of the brake caliper, cleaning the hub, reassembling the caliper and final check.

Withdrawal of the brake disc in 5 simple steps with the necessary tools.
⚙️

Before changing the brake disc on your Peugeot 207 in 5 easy steps, it is essential to prepare with the appropriate tools. Make sure you have a jack, jack stands, lug wrench, slotted screwdriver, ratchet with sockets, brake cleaner, and brake rotors appropriate for your model.
The first step is to slightly loosen the wheel nuts while holding the car on the ground, then lift the Peugeot 207 with the jack and place the jack stands under the recommended lifting points.
Next, remove the wheels to access the brake calipers, taking care to remove the worn calipers and brake rotors. Before installing the new rotors, clean the contact surface with the hub with brake cleaner.
Install the new brake discs following the disassembly direction, replace the brake calipers and secure the retaining clips correctly. Finally, put the wheels back in place, hand-tighten the nuts and lower the car back to the ground.
In conclusion, tighten the wheel nuts, carry out a moderate test to check that the brakes are working correctly, and you will be able to change the brake disc on your Peugeot 207 easily by following these 5 clear steps.

🔧 Unscrew the wheel nuts
🔩 Remove the wheel
🔧 Unscrew the brake disc fixing system
🔄 Replace the worn brake disc with the new disc
🔧 Replace the fixing system and tighten

🛠️ How to change the brake disc of your Peugeot 207 in 5 easy steps?

  1. Check the brake disc and pads for wear 🧐
  2. Unscrew the brake disc mounting screws 🔧
  3. Remove the used brake disc by sliding it 👋
  4. Install the new brake disc and screw in the fixings 🔩
  5. Remount the wheels and perform a braking test 🚗

Preparation and necessary tools

Before you start changing the brake discs of your Peugeot 207, it is essential to prepare well and gather the necessary tools. Here is a list of items you will need:

  • A jack and jack stands to raise and secure the car.
  • A lug wrench to remove the wheels.
  • A flat screwdriver to remove the retaining clips.
  • A ratchet with sockets for removing brake calipers.
  • A brake cleaner to clean the parts in contact.
  • A set of new brake discs adapted to your Peugeot model.

Ensuring the condition of your tools is crucial to avoid any problems during the intervention. Once everything is ready, you can move on to the next step.

Start by loosening the wheel nuts slightly while holding the car on the ground. This will make it easier to remove the wheels once the car is raised. Then use the jack to raise the Peugeot 207 and place the jack stands under the lifting points recommended by the manufacturer.

Remove the wheels to access the brake rotors. Proceed with caution when removing the brake calipers using the appropriate ratchet and sockets. Don’t forget to detach the pad fixing clips using the flat screwdriver. Once the calipers are removed, extract the used brake discs.

Before installing the new discs, carefully clean the contact surface with the hub using brake cleaner. This step guarantees clean assembly and avoids any premature wear.

Install the new brake discs following the direction of removal. Then replace the brake calipers and secure the retaining clips correctly. Finally put the wheels back in place and tighten the nuts by hand before lowering the car back to the ground.

Finally, be sure to tighten the wheel nuts once the car is on the ground. Perform a moderate test to ensure the brakes are functioning properly.

Hardware check

Before you begin, it is vital to gather all the necessary tools to change the brake disc of your Peugeot 207. You will need:

  • A jack and jack stands to lift and secure the vehicle
  • An adjustable wrench and various sockets
  • A slotted screwdriver and a Phillips screwdriver
  • A rubber hammer
  • Brake lubricant and a clean cloth

First step: Lift your Peugeot 207 using the jack and secure it with the jack stands. Make sure the car is stable before continuing.

Then remove the wheel by unscrewing the nuts with the adjustable wrench. Set the nuts aside so you don’t lose them.

Step Three: Once the wheel is removed, access the brake caliper. Use the flathead screwdriver to lightly push the brake pads inward, creating a gap. Unscrew the caliper bolts with the appropriate socket and carefully remove it. Hang the caliper with a wire to avoid damaging the brake hose.

Step Four: Remove the worn brake discs. Sometimes they can be stuck by rust or dirt. Use the rubber hammer to lightly tap the disc to remove it. Then clean the mounting surface with the cloth and brake lubricant.

Finally, install the new brake rotors, aligning them correctly. Replace the brake caliper and tighten the bolts securely. Reinstall the wheel and tighten the nuts, making sure they are secure. Lower the car and check that everything is in place.

It is advisable to test the brakes at low speeds to ensure they are functioning properly before resuming normal driving.

Preparing the car

Change the brake disc of your Peugeot 207 can seem intimidating, but with the right tools and proper preparation, it’s a task you can tackle yourself. Here’s what you’ll need to have on hand before you start:

  • A jack and jack stands
  • A set of socket wrenches
  • A flat screwdriver
  • A pliers
  • A metal brush
  • Brake cleaner
  • Brake lubricant
  • New brake discs
  • A torque wrench

Start by parking your Peugeot 207 on a flat and stable surface. Tighten it hand brake and place chocks behind the rear wheels to prevent movement.

Use the jack to lift the car and secure it with jack stands. Make sure the car is stable before working under it.

Remove the wheel covers (if present) and unscrew the wheel nuts using the socket wrench. Remove the wheel to access the braking system.

Using the flathead screwdriver, remove the brake pad retaining clips. Use the pliers to remove the springs holding the pads if necessary.

Unscrew the brake caliper bolts using the socket wrench and remove the caliper. Suspend it with a piece of wire or rope so as not to put tension on the brake hose.

Use the wire brush and brake cleaner to clean the residue from the hub and brake rotor carrier. Then apply a little brake lubricant to prevent corrosion.

Mount the new brake rotors onto the hub and secure them with the appropriate bolts. Fit the brake caliper over the new rotor and tighten the bolts using the torque wrench to the manufacturer’s specifications.

Everything is almost finished! Reassemble the pads, springs and clips in the reverse order of disassembly. Replace the wheel and tighten the nuts evenly, then lower the car to the ground.

Necessary tools

Before starting to replace the brake disc on your Peugeot 207, make sure you have all the necessary tools. Preparation and organization are the keys to a successful repair.

  • Adjustable wrench
  • Torque wrench
  • Flat head screwdriver
  • Jacks and jack stands
  • Socket case
  • Lever arm
  • Safety equipment (gloves and protective glasses)

Also make sure you have the correct replacement part. Check that the new brake disc is compatible with the model and year of your Peugeot 207.

1. Raise the car : Use the jacks to carefully raise the car and place the jack stands under the chassis to secure the vehicle.

2. Remove the wheel : Using the adjustable wrench, unscrew the wheel bolts and remove it to access the brake disc.

3. Remove the brake caliper : Use a socket wrench to remove the bolts holding the caliper. Hang the caliper with a wire to avoid pulling on the brake hose.

4. Remove the brake disc : Remove the disk retaining screws with a screwdriver and remove the worn disk.

5. Install the new disk : Position the new disc on the hub and tighten the retaining screws. Replace the caliper and wheel, then lower the car back to the ground.

By following these five steps, you can easily replace the brake disc on your Peugeot 207 and get back on the road in complete safety.

Changing the brake disc

To change the brake disc of your Peugeot 207, follow these five simple steps.

Step 1: Preparing the vehicle

Make sure the car is on a flat, stable surface. Use a jack to raise the vehicle and place it on jack stands to ensure your safety. Remove the wheel by unscrewing the nuts using a suitable wrench.

Step 2: Accessing the brake disc

Once the wheel is removed, locate the brake caliper. Unscrew the bolts that secure the caliper to the disc bracket. Hang the caliper using a wire or rope to avoid straining the brake hose.

Step 3: Removing the Used Disc

Remove the caliper bracket by unscrewing the fixing screws. Next, remove the screws holding the brake disc if they exist. Lightly tap the disc with a rubber mallet to release it from its slot.

Step 4: Installing the New Disk

Clean the wheel hub thoroughly with a wire brush to remove rust and dirt. Place the new brake disc on the hub, making sure that the retaining screw holes (if present) are properly aligned. Screw in the retaining screws and secure the caliper bracket by tightening the screws securely.

Step 5: Reassembly and Checking

  • Replace the caliper and tighten the mounting bolts.
  • Check that everything is tight and that the components are correctly positioned.
  • Reinstall the wheel and tighten the nuts crosswise to ensure even pressure distribution.
  • Lower the car to the ground and tighten the lug nuts to their recommended torque.
  • Gently pump the brake pedal to bring the pads back into contact with the new rotor.

There you go, you have finished the changing the brake disc of your Peugeot 207 successfully. Don’t forget to test the brakes by taking a short, safe test drive.

Removing the wheel

To change the brake disc of your Peugeot 207, start by gathering all the necessary tools: a jack, jack stands, a torque wrench, a socket wrench and a screwdriver. Also make sure you have the new brake pads and rotors compatible with your vehicle.

Place your car on a flat surface and apply the handbrake. Loosen the wheel nuts slightly before jacking up the car. Position the jack stands under the vehicle for added security, then remove the nuts completely and remove the wheel.

Next, you will need to have access to the brake caliper. Use the socket wrench to loosen the bolts holding it in place. Once the bolts are removed, you can release the caliper and hang it with a piece of wire or place it gently so as not to damage the brake hose.

Now remove the old brake pads. Use a screwdriver to remove the screws holding the drive in place. In some cases, you may need to give a few light taps with a rubber hammer to loosen the disc from the axle.

Clean the axle thoroughly before installing the new disc. Make sure it is correctly positioned and replace the fixing screws. Install the news brake pads and make sure they are securely in place.

Reassemble the brake caliper by tightening it with the bolts. Then put the wheel back in place and tighten the nuts by hand before lowering the vehicle to the ground. Finalize the tightening of the nuts using the torque wrench following the manufacturer’s specifications.

To check that everything is in order, take a test drive on a quiet road. Check that the brakes respond correctly and smoothly.

Disassembly of the brake caliper

THE changing the brake disc of your Peugeot 207 is an essential operation to guarantee your safety on the road. Here’s how to make it in 5 simple steps.

Start by securing your vehicle. Use a jack to raise the vehicle and place jack stands for added safety. Then remove the wheel to access the braking system.

Disassembly of the brake caliper

Use a suitable wrench to loosen the brake caliper bolts. Carefully lift the caliper and hang it with a wire so as not to damage the brake hose. Once the caliper is clear, remove the brake pads.

Remove the caliper bracket by unscrewing the two large screws holding it in place. The way is then clear to access the brake disc.

Remove the used brake disc by pulling it towards you. If it gets stuck, you can use a rubber mallet to dislodge it.

Before installing the new brake rotor, clean the hub surface thoroughly with a wire brush to remove any rust and dirt. Then place the new brake disc on the hub.

Reassemble the caliper bracket and tighten the screws. Replace the brake pads and reposition the caliper, making sure everything is aligned properly. Tighten the caliper bolts securely.

Reinstall the wheel and tighten the nuts. Carefully lower the vehicle and do a final check to make sure everything is in place correctly.

Test your braking for a short distance at low speed to ensure the brakes are working properly.

Removing the brake disc

Changing the brake discs on your Peugeot 207 is an essential operation to guarantee your safety on the road. Here’s how to do it in five simple steps.

Necessary material :

  • Jacks and jack stands
  • Nut wrench
  • Screwdriver
  • Wheel nut
  • New disc brake

Removing the brake disc:

1. Lift the car : Use a jack to lift your Peugeot 207, then place it on jack stands for added safety. Make sure the vehicle is stable before starting work.

2. Remove the wheel : Using a lug wrench, loosen and remove the wheel nuts. Then remove the wheel to access the brakes.

3. Remove the brake caliper : Use a screwdriver or wrench to remove the caliper mounting bolts. Once the bolts are removed, gently remove the brake caliper and hang it using a hook or rope to avoid damaging the brake cables.

4. Remove the brake disc : With the caliper removed, you can now access the brake disc. Unscrew the screws securing the disk, then remove it. If the disc is stuck, lightly tap it with a rubber mallet to dislodge it.

5. Install the new brake disc : Position the new brake disc in place of the old one and secure it with the fixing screws. Then reassemble the brake caliper by placing it back on the disc and securing the caliper bolts.

Reassembly:

1. Reinstall the wheel : Place the wheel back on the hub and tighten the wheel nuts crosswise to ensure an even fit.

2. Lower the car : Use the jack to slightly raise the car and remove the jack stands. Then lower the car to the ground smoothly.

3. Test the brakes : Before getting back on the road, pump the brake pedal several times to make sure everything is working properly. Carry out a test while driving carefully to verify that the brakes respond properly.

By following these steps, you will be able to change the brake discs on your Peugeot 207 safely and efficiently.

Q: What is the first step to take to change the brake disc on my Peugeot 207?

A: Before you begin, make sure you park your car on a level surface and secure the vehicle by putting the handbrake on and blocking one wheel with a wheel chock.

Q: What tools do I need to change the brake disc on my Peugeot 207?

A: The main tools needed are a ratchet, sockets, jack and jack stands, flat screwdriver, rubber mallet and piston pusher.

Q: How do I remove the old brake disc from my Peugeot 207?

A: To remove the old brake disc, you must first disassemble the brake caliper, then remove the screws that hold the disc in place. Then, simply remove the worn disc and replace it with a new one.

Q: How do I install the new brake disc on my Peugeot 207?

A: To install the new brake disc, you must first clean the mounting surface, then place the new disc in its position. Then, retighten the fixing screws and reassemble the brake caliper.

Q: What precautions should I take after changing the brake disc on my Peugeot 207?

A: After replacing the brake disc, it is recommended to check the brake fluid level and test braking on a quiet road before returning to normal driving.